A-Silicone

Дата Продукт Описание
12/2022 AFFINIS Trueness of full-arch dental models obtained by digital and conventional impression techniques: an in vivo study
02/2020 PRESIDENT Local accuracy of actual intraoral scanning systems for single-tooth preparations in vitro
10/2019 Magic FoamCord A Comparative Evaluation of Efficacy of Gingival Retraction Using Polyvinyl Siloxane Foam Retraction System… A Comparative Evaluation of Efficacy of Gingival Retraction Using Polyvinyl Siloxane Foam Retraction System, Vinyl Polysiloxane Paste Retraction System, and Copper Wire Reinforced Retraction Cord in Endodontically Treated Teeth: An in vivo Study
08/2019 AFFINIS Moderne Werkstoffe zur Abformung und Bissregistrierung
05/2019 PRESIDENT Accuracy of complete- and partial-arch impressions of actual intraoral scanning systems in vitro
08/2017 AFFINIS A Comparative Analysis of Master Casts Obtained using Different Surface Treatments on Impression Copings for Single Tooth Implant Replacement - An In vitro Study
08/2017 AFFINIS Accuracy of a separating foil impression using a novel polyolefin foil compared to a custom tray and a stock tray technique
11/2015 AFFINIS Dimensional Stability of Two Polyvinyl Siloxane Impression Materials in Different Time Intervals
05/2015 PRESIDENT Accuracy and precision of silicon based impression media for quantitative areal texture analysis
12/2014 AFFINIS A Comparative Evaluation of Dimensional Accuracy and Surface Detail Reproduction of Four Hydrophilic Vinyl Polysiloxane Impression Materials Tested Under Dry, Moist, and Wet Conditions-An In Vitro Study A Comparative Evaluation of Dimensional Accuracy
12/2014 AFFINIS An evaluation of the fit of metal-ceramic restorations made with an autoclaved silicone-based impression material.
01/2014 AFFINIS Analysis of autoclave induced dimensional changes on addition silicones
12/2013 AFFINIS Evaluation of Dimensional Stability and Accuracy of Autoclavable Polyvinyl Siloxane Impression Material
06/2013 AFFINIS Comparison of elastomeric impression materials' thixotropic behavior.
05/2013 AFFINIS Surface Roughness of PVS IM Following Chemical Disinfection, Autoclave and Microwave Sterilization
08/2012 AFFINIS Precision and Handling of A-silicon versus Polyether for Implant Impressions
03/2011 PRESIDENT The dimensional stability of impression materials and its effect on in vitro tooth wear studies
01/2011 AFFINIS Evaluation of Dimensional Stability of Autoclavable Elastomeric Impression Material
07/2010 AFFINIS Effect of Autoclave Sterilisation on the Dimensional Stability and Tear Strength of Three Silicone Impression Materials
05/2007 AFFINIS Quality of impressions using hydrophilic polyvinyl siloxane in a clinical study of 249 patients.
09/2004 AFFINIS Accuracy of different polyvinylsiloxanes: A Clinical pilot study
08/2004 AFFINIS Klinisch erreichbare Abformgenauigkeit von A-Silikonen
09/2003 PRESIDENT The influence of handling on the elasticity of addition silicone putties
07/2003 AFFINIS Selected Characteristics of a New Vinyl Polysiloxane Impression Material: A Randomized Clinical Trial
04/2001 PRESIDENT Effect of wash bulk on the accuracy of polyvinyl siloxane putty-wash impressions
05/1999 AFFINIS Dimensional stability of addition cured silicone impressions following autoclave sterlisation
11/1998 PRESIDENT Rheological Properties of Elastomers Before and During Setting
08/1988 PRESIDENT Review of Dental Impression Materials
02/1983 PRESIDENT Curing contraction of addition-type silicone impression materials
12/1982 PRESIDENT Thermal expansion of addition polymerization (Type II) silicone impression materials

C-Silicone

Дата Продукт Описание
09/2021 Speedex Comparing the Dimensional Accuracy of Casts Obtained from Two Types of Silicone Impression Materials in Different Impression Techniques and Frequent Times of Cast Preparation
04/2020 Speedex Effect of Core Materials on the Dimensional Accuracy of Casts Made of Two Different Silicone Impression Materials: An Experimental Study
03/2020 PSI Evaluation of Film Thickness of Crown Disclosing Agents and Their Comparison with Cement Film Thickness after Final Cementation Evaluation of Film Thickness of Crown Disclosing Agents and Their Comparison with Cement Film Thickness after Final Cementation
03/2016 Coltex Comparison of the surface roughness of gypsum models constructed using various impression materials and gypsum products
09/2015 Speedex The effect of spraying different disinfectants on condensational silicone impressions; an in vitro study
04/2014 Speedex Effect of Autoclave Sterilisation on the Dimensional Stability and Tear Strength of Three Silicone Impression Materials
10/2011 Speedex Characterization of some Condensation Silicone Impression Materials